GB 5009.6 is the Chinese national food safety standard for the determination of fat (crude fat) in food products, providing three official methods based on Soxhlet extraction, acid hydrolysis, and alkali hydrolysis. Accurate crude fat analysis is essential for nutrition labeling, regulatory compliance, and quality control across cereals, meats, dairy, nuts, baked goods, and infant formula. This article explains the technical principles, sample requirements, procedures, and practical applications of GB 5009.6 testing as performed by accredited third-party laboratories.
Technical Overview
GB 5009.6-2016, titled "National Food Safety Standard — Determination of Fat in Foods," is the mandatory Chinese national standard that specifies the analytical methods for measuring fat content in food matrices. It superseded the previous GB/T 5009.6-2003 method and is issued under the GB 5009 series of food safety testing standards administered by China's national health authorities. The standard is directly referenced in product standards, nutrition labeling regulations (such as GB 28050), and market surveillance programs for foods sold in China.
The standard defines "crude fat" as the totality of substances soluble in approved organic solvents under the prescribed conditions. This includes triglycerides and other lipids such as free fatty acids, phospholipids, sterols, pigments, and fat-soluble vitamins, which is why the result is conventionally reported as "crude fat" rather than pure triglyceride content. GB 5009.6-2016 establishes three first-level methods: the Soxhlet extraction method (Method I) for free fat in dry, low-moisture foods; the acid hydrolysis method (Method II) for foods in which fat is bound within starch or protein matrices; and the alkali hydrolysis method (Method III) for milk and dairy products.
Method selection depends on the physical state of the sample, its matrix composition, and the form in which the fat is present. Unless otherwise specified in a product standard, the applicable method stated for that food category governs. The determination is gravimetric: solvent extracts are evaporated, the residual fat is dried to constant mass, and results are expressed in grams per 100 grams (g/100 g) of sample.
Testing Samples
Cereals, Grains, and Grain Products
Wheat flour, rice, noodles, corn, oats, and other cereal products typically contain low to moderate fat levels, some of which is bound within starch granules. Depending on the product standard, such samples may be analyzed by direct Soxhlet extraction or by acid hydrolysis when bound fat must be released before extraction.
Meat, Poultry, and Processed Meat Products
Fresh meat, sausages, cured products, and canned meats contain high levels of both visible adipose tissue and intramuscular fat. Dried, homogenized meat samples are generally suited to Soxhlet extraction, while emulsified or highly processed products may require hydrolysis to release lipid material fully encapsulated by protein.
Dairy Products
Liquid milk, fermented milk, milk powder, cream, cheese, and formulated dairy beverages fall under the alkali hydrolysis method, in which ammonia breaks the protein–fat complexes (particularly casein micelles) so that the fat can be quantitatively extracted with ether-based solvents.
Nuts, Seeds, and Legumes
Peanuts, sunflower seeds, sesame, soybeans, and tree nuts contain high fat concentrations, often above 40 g/100 g. These samples are dried, ground, and extracted by the Soxhlet method, with careful control of sample mass to stay within the operational range of the balance and extraction apparatus.
Baked Goods, Snacks, and Fried Foods
Biscuits, potato chips, instant noodles, and fried snacks contain absorbed frying oil plus varying degrees of moisture and bound lipid. Sample pretreatment, including drying and grinding, is critical for reproducible results, and hydrolysis may be applied where the product standard requires total fat.
Infant Formula, Special Dietary Foods, and Condiments
Infant formula, nutritional powders, sesame paste, and similar products combine protein, carbohydrate, and lipid phases. The appropriate method is selected according to the matrix: milk-based formulas follow the alkali hydrolysis approach, while cereal-based or mixed products may be tested by acid hydrolysis or Soxhlet extraction as specified.
Testing Items
Testing under GB 5009.6 is typically reported as one or more of the following items:
- Crude fat content by Soxhlet extraction (free/solvent-extractable fat), expressed in g/100 g
- Total fat after acid hydrolysis (free fat plus fat released from starch and protein complexes), expressed in g/100 g
- Total fat after alkali hydrolysis (for milk and dairy matrices), expressed in g/100 g
- Fat content on a dry basis or as-received basis, depending on the product standard and client requirements
- Supporting parameters such as sample moisture, which is needed for dry-basis reporting
Results are compared against the limits declared in the applicable product standard or against the nutrition label declared values for compliance assessment.
Testing Methods
Method I: Soxhlet Extraction
A representative, homogenized sample is dried and ground, and an accurately weighed portion (typically 1 g to 10 g, depending on expected fat content, weighed to 0.1 mg) is placed in a cellulose extraction thimble. The sample is extracted in a Soxhlet apparatus with anhydrous diethyl ether or petroleum ether (boiling range 30 °C to 60 °C) under continuous reflux for approximately 6 to 8 hours, or until extraction is complete. The solvent is recovered, the extraction flask containing the fat residue is dried at 100 °C to 105 °C in an oven to constant mass, cooled in a desiccator, and weighed. Crude fat is calculated as the mass difference of the flask before and after extraction relative to the sample mass. This method is suited to dry samples in which fat is largely free and directly extractable, and it is not applicable to dairy products.
Method II: Acid Hydrolysis
For foods in which fat is encapsulated or bound, an accurately weighed sample (approximately 2 g of solid material or 10 g of liquid material) is heated with hydrochloric acid at 70 °C to 80 °C for roughly 30 to 60 minutes to hydrolyze carbohydrate and protein matrices and liberate the bound lipid. After cooling, ethanol is added, and the hydrolysate is transferred to an extraction tube or measuring cylinder. The liberated fat is extracted repeatedly with diethyl ether and petroleum ether, and the combined ether layers are evaporated. The residual fat is dried to constant mass at 100 °C to 105 °C and weighed gravimetrically. This method applies to cereals, grain products, starch-based foods, and other matrices where simple solvent extraction underrecovers fat.
Method III: Alkali Hydrolysis
Designed for milk and dairy products, this method uses concentrated ammonia solution to disrupt protein–fat emulsions, particularly casein-bound fat. The sample is dispersed in water in a Mojonnier-type extraction tube, treated with ammonia in a warm water bath, mixed with ethanol to improve phase separation, and then extracted with successive portions of diethyl ether and petroleum ether. The combined extracts are evaporated, and the fat residue is dried to constant mass and weighed. This approach achieves quantitative recovery of milk fat and is compatible with liquid, semi-solid, and reconstituted powdered dairy samples.
Equipment, Reagents, and Key Conditions
- Analytical balance with 0.1 mg readability for gravimetric determination
- Soxhlet extractors, condensers, and fat extraction flasks; electric or water-bath heating units
- Anhydrous diethyl ether (free of peroxides) and petroleum ether (30 °C to 60 °C boiling range) of analytical grade
- Hydrochloric acid, ammonia solution, and ethanol (95 percent) for the hydrolysis methods
- Forced-draft or gravity convection oven at 100 °C to 105 °C and desiccator with effective desiccant
- Cellulose extraction thimbles, grease-free glassware, and explosion-proof solvent handling facilities
Quality Control and Precision
Each analytical batch includes reagent blanks and duplicate determinations. Constant weight is verified by repeated drying and weighing cycles until successive weighings agree within the tolerance set by the standard (typically on the order of 1 mg to 2 mg). Under repeatability conditions, the absolute difference between two independent determinations must not exceed the limit specified in the standard for the relevant method and concentration level, commonly expressed as a relative deviation in the range of 5 percent to 10 percent. Solvent purity, complete sample drying before extraction, prevention of moisture uptake by dry residues, and full recovery of solvent (for both safety and cost control) are the principal sources of error requiring systematic control.
Applications
- Nutrition labeling compliance: verification of declared fat values in accordance with GB 28050 nutritional labeling requirements
- Product standard conformity: demonstrating conformity with fat limits in commodity standards for cereals, meats, dairy, and snack foods
- Manufacturing quality control: monitoring recipe consistency, oil absorption in frying processes, and cream separation stability
- Shelf-life and stability studies: tracking lipid changes during storage as part of broader rancidity assessment programs
- Import and export inspection: providing recognized test results for customs clearance and trade documentation
- Research and product development: comparing fat delivery across formulations of infant formula, plant-based foods, and functional products
- Audit and certification support: supplying data for food safety management system verification and regulatory inspections
Because GB 5009.6 is a national food safety standard, laboratories performing the test for compliance purposes should hold appropriate accreditation, such as ISO/IEC 17025, with the method within their accredited scope.
FAQ
What is the difference between crude fat and total fat in GB 5009.6?
Crude fat refers to all substances extracted by the solvent under the specified conditions, including triglycerides plus phospholipids, sterols, pigments, and fat-soluble compounds. Soxhlet extraction measures mostly free, extractable fat, while the hydrolysis methods release fat bound in protein or carbohydrate matrices, yielding a value closer to total fat. The appropriate choice is defined by the applicable product standard.
Which method should be used for dairy products?
Milk and dairy products are determined by the alkali hydrolysis method, because milk fat is stabilized within protein emulsions that resist direct solvent extraction. Ammonia treatment releases the fat so that ether extraction can recover it quantitatively.
Why is acid hydrolysis necessary for some foods?
In baked goods, cereals, and starch-rich products, a portion of the lipid is physically encapsulated or chemically bound within the matrix. Direct Soxhlet extraction of such samples can underreport fat. Acid hydrolysis breaks down the matrix and releases the bound fat before solvent extraction, ensuring complete recovery.
Why must the sample be dried before Soxhlet extraction?
Moisture in the sample prevents the nonpolar extraction solvent from penetrating the matrix and contacting the fat, leading to low and irreproducible recovery. Water in the extraction system can also co-extract water-soluble contaminants into the flask, biasing the gravimetric result.
How are results calculated and reported?
The fat content is calculated as the mass of dried fat residue divided by the sample mass, multiplied by 100, and reported in g/100 g. A blank correction is applied by subtracting the residual mass obtained from a reagent blank run through the full procedure.
How is GB 5009.6 related to international methods?
GB 5009.6 is technically aligned with internationally recognized gravimetric fat determinations, such as the Soxhlet-type procedures published by AOAC International and ISO (for example, ISO methods for fat in milk and feeding stuffs). Results obtained by GB 5009.6 are generally acceptable for Chinese regulatory purposes, while ISO or AOAC methods may be required for other jurisdictions; accredited laboratories can advise on method equivalence for specific trade scenarios.
How long does a GB 5009.6 determination take?
A single Soxhlet determination typically requires 6 to 8 hours of extraction plus drying, cooling, and weighing cycles, so routine turnaround for a validated batch is commonly several working days including sample preparation, duplicates, and reporting. Hydrolysis methods require additional hydrolysis and multi-stage extraction time.
What sample precautions are important for accurate results?
- Homogenize the sample thoroughly so the analytical portion is representative
- Minimize fat loss and oxidation by avoiding prolonged exposure to heat, light, and air during preparation
- Verify that diethyl ether is peroxide-free and that solvents leave no measurable residue on evaporation
- Cool dried flasks in a desiccator and weigh promptly to prevent moisture uptake by the fat residue
- Observe solvent safety requirements, including explosion-proof equipment and fume extraction
Can GB 5009.6 results be used for nutrition labels?
Yes. Fat values determined by GB 5009.6 are the standard basis for verifying fat declarations on prepackaged food labels in China. Declared values must comply with the tolerance criteria defined in the nutrition labeling standard, and testing should be performed by an accredited third-party laboratory with the method in scope.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing