PET flake screening testing is a systematic laboratory evaluation of washed recycled PET bottle flakes that verifies critical quality parameters such as intrinsic viscosity, contamination levels, moisture, and color before the material enters food-contact or industrial supply chains. This technical guide explains the scope of PET flake screening inspection, the sample grades involved, the key testing items, the analytical methods applied, and the standards that govern lot acceptance. It is designed to help recyclers, converters, and buyers build reliable incoming quality control and supplier qualification programs.
Technical Overview
Polyethylene terephthalate (PET) bottle flakes are produced by collecting, sorting, grinding, hot- or cold-washing, and drying post-consumer or post-industrial PET bottles. The resulting flake is the primary feedstock for recycled PET (rPET) used in bottle-to-bottle packaging, polyester fiber, extruded sheet, and strapping. Because flake quality is determined by the consistency of the entire recycling chain, small variations in sorting, washing temperature, or contamination control can cause significant downstream processing defects.
PET flake screening inspection is a targeted battery of rapid, statistically sampled laboratory tests used to verify that a flake lot conforms to purchase specifications, to compare the consistency of different suppliers, and to confirm suitability for a specific end application. It typically combines rheological, thermal, optical, physical, and chemical analyses into a single decision package that supports acceptance, rejection, or supplier ranking.
- Verify conformance of each lot against agreed technical specifications
- Detect and quantify contamination such as PVC, polyolefins, metals, adhesives, and colored PET
- Confirm processing stability by checking intrinsic viscosity, moisture, and bulk density
- Support supplier qualification, incoming inspection, and trade settlement between recyclers and converters
- Provide baseline evidence for food-contact compliance programs and regulatory submissions
Screening programs are commonly executed by accredited third-party laboratories or in-house quality departments using methods published by standards organizations such as ISO, ASTM, EN, and GB, alongside applicable food-contact regulations.
Testing Samples
Samples are drawn from filled big bags, silos, or containers using a sampling plan proportional to lot size. A representative screening sample is typically 2 to 5 kg of flake, homogenized and divided before testing.
Hot-Washed Clear PET Flakes
The premium grade obtained from clear bottles after caustic hot washing. This material is intended for high-value applications, including food-contact packaging and virgin PET substitution, and is subject to the most stringent screening limits.
Cold-Washed and Fiber-Grade Flakes
Flakes washed at lower temperatures, often containing a controlled share of colored or tinted PET. They are screened mainly for fiber spinning and general extrusion, where color and contamination limits are wider but intrinsic viscosity and moisture remain critical.
Blue and Tinted PET Flakes
Flakes from blue-tinted water and beverage bottles, frequently used in fiber or mixed back into clear streams at defined ratios. Screening focuses on color coordinates, tint strength, and cross-contamination between color fractions.
Unwashed and Post-Industrial Flake Streams
Material from industrial skeletons, start-up lumps, or dry-ground bottles. Screening emphasizes surface contamination, label and glue residue, moisture, and foreign polymer content to establish wash-line performance expectations.
Testing Items
A screening report is normally organized into five groups of parameters, each linked to a defined acceptance limit agreed between buyer and seller.
Physical and Rheological Properties
- Intrinsic viscosity (IV), expressed in dL/g, the single most important quality indicator
- Bulk density, which affects extruder feeding and throughput
- Flake size distribution and fines content
- Melting point and thermal transitions for polymer identity confirmation
Contamination Screening
- PVC content, typically required below 50 to 100 ppm due to its severe degradation effect
- Polyolefin contamination (PE and PP from caps and rings)
- Other non-PET polymers such as PLA, PS, PETG, and PA identified by spectroscopy
- Ferrous and non-ferrous metal particles, sand, glass, and grit
- Glue, label residue, paper, wood, and textile fibers
- Colored PET flakes within clear grades, reported in ppm
Moisture and Volatiles
- Total moisture content, typically specified below 0.5 percent
- Acetaldehyde residue, a key concern for bottle-to-bottle applications
- General volatile organic compounds remaining from contents or washing chemistry
Optical Properties
- CIE color coordinates L*, a*, and b* measured on a defined flake pad
- Yellowness index and whiteness trend compared against reference standards
- Visual defect rating under standardized lighting
Chemical and Regulatory Compliance
- Ash content as an indicator of inorganic residues and fillers
- Heavy metals including antimony, lead, cadmium, mercury, and arsenic
- Overall and specific migration testing for food-contact verification
- Screening for non-intentionally added substances (NIAS) where required by the buyer or regulation
Testing Methods
Intrinsic Viscosity by Solution Viscometry
Intrinsic viscosity is measured by dilute-solution viscometry using an Ubbelohde capillary or an automated relative viscometer, following ISO 1628-5 or ASTM D4603 with phenol-based solvent systems at 25 degrees Celsius. The result directly reflects the molecular weight of the PET and its expected strength after processing. Rapid melt-flow or capillary methods are frequently used in parallel for high-throughput in-plant screening.
Thermal Analysis by DSC and TGA
Differential scanning calorimetry per ISO 11357 or ASTM D3418 confirms polymer identity through the PET melting point of approximately 250 degrees Celsius and can reveal foreign polymer peaks from PETG, PLA, or polyolefins. Thermogravimetric analysis per ISO 11358 or ASTM E1131 quantifies PVC through its characteristic degradation step and simultaneously determines ash residue.
Polymer Identification by Infrared Spectroscopy
FTIR spectroscopy is applied to individual suspect particles picked during manual or automated sorting, confirming whether a contaminant is PVC, polyolefin, or another resin. This method is the standard reference for resolving disputed particle identification in screening reports.
Moisture Determination
Moisture is measured by Karl Fischer titration in accordance with ASTM D6869 or by validated oven and halogen moisture analyzers. Accurate moisture data is essential because excessive water causes hydrolytic chain scission during extrusion, reducing intrinsic viscosity and mechanical performance.
Contamination Quantification by Separation and Sorting
Float-and-sink separation in water separates floating polyolefins from sinking PET, with results expressed in ppm. Manual inspection of a defined flake mass under controlled lighting quantifies visible defects such as colored flakes, glue spots, and metals. Metal detection is supported by ashing and, where required, by elemental techniques.
Sieve Analysis for Flake Size Distribution
Flake size is determined with a calibrated sieve stack following the principles of ISO 2591-1, reporting the mass fraction retained on each aperture. Oversize flakes and excessive fines both influence washing efficiency, drying behavior, and extruder feeding.
Color Measurement
Color coordinates L*, a*, and b* are measured with a calibrated spectrophotometer using methods consistent with ISO 11664 and ASTM E308, typically on a compressed flake pad with a defined thickness and backing. Yellowness index is tracked as a sensitive indicator of thermal or oxidative degradation.
Elemental and Migration Analysis
Heavy metals are screened by X-ray fluorescence and quantified by ICP-OES or ICP-MS. Acetaldehyde and volatile residues are quantified by headspace GC-MS. Food-contact verification is performed through overall and specific migration testing using food simulants in line with applicable regulations such as EU Regulation No 10/2011, US FDA 21 CFR 177.1630, and the Chinese food-contact plastic standard GB 4806.7.
Applications
Screening inspection results directly determine which applications a PET flake lot can serve, and consistent screening data is the foundation of long-term supplier qualification.
- Bottle-to-bottle recycling, where IV, color, PVC, acetaldehyde, and migration results must all fall within tight limits
- Polyester staple fiber and filament spinning, which depend primarily on IV stability and moisture control
- Extruded PET sheet and thermoformed packaging for food and non-food trays
- PET strapping and industrial monofilament requiring consistent strength
- Compounding and blending, where screening data defines rPET loading ratios against virgin resin
- Trade verification, customs and settlement disputes, and annual supplier audits
FAQ
What is the difference between screening testing and full compliance testing?
Screening testing is a rapid, specification-focused program used to accept or reject flake lots, typically completed within a few working days. Full compliance testing, in contrast, is a comprehensive regulatory assessment including complete migration panels and toxicological evaluation, usually reserved for process approval or product certification.
What intrinsic viscosity range is acceptable for PET flakes?
Bottle-grade flakes are generally specified between 0.72 and 0.85 dL/g, fiber grades between 0.60 and 0.72 dL/g, and sheet grades around 0.70 to 0.80 dL/g. If IV is too low after recycling, solid-state polycondensation can restore molecular weight before final processing.
Why is PVC contamination so critical in PET flakes?
PVC decomposes at PET processing temperatures and releases hydrogen chloride, which causes yellowing, embrittlement, intrinsic viscosity loss, and equipment corrosion. Even at concentrations of a few hundred ppm it can ruin an entire extrusion batch, which is why most specifications demand levels below 50 to 100 ppm.
How much sample is required for a screening program?
A representative sample of 2 to 5 kg is sufficient for the physical, thermal, and optical portions of screening. Migration and elemental compliance testing may require additional material, and accredited third-party laboratories usually retain sealed counter-samples for dispute resolution.
Can PET flakes be certified for food contact through screening alone?
No. Food-contact status is granted to a recycling process, not to an isolated flake lot, and requires a challenge test demonstrating contaminant removal efficiency under the relevant regulatory framework. Screening of the resulting flakes provides ongoing verification that the approved process remains under control.
How long does a typical screening program take?
Routine screening covering IV, moisture, contamination, color, and thermal identity is generally completed within three to seven working days. Migration and NIAS investigations extend the timeline to several weeks depending on the simulants and conditions selected.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing