Ubicación: Global + English
Global Global Algérie Français Algeria English Angola Português Angola English Argentina Español Argentina English Australia English Austria Deutsch Austria English Azerbaijan English Azerbaijan Русский Bahrain English Bangladesh English Belgium English Belgium Français Belgium Nederlands Brazil Português Brazil English Bulgaria български Bulgaria English Cameroon English Cameroon Français Canada English Canada Français Chile Español Chile English China 中文 China 日本語 China English Colombia Español Colombia English Croatia English Czech Republic Čeština Czech Republic English Denmark English Djibouti English Ecuador Español Ecuador English Egypt English Estonia English Ethiopia English Finland Suomi Finland English France Français France English Georgia English Georgia Русский Germany Deutsch Germany English Ghana English Greece Ελληνικά Greece English Guatemala Español Guatemala English Hong Kong, China English Hong Kong, China 中文 Hungary Magyar Hungary English India English Indonesia English Iraq English Ireland English Italy Italiano Italy English Ivory Coast Français Ivory Coast English Japan 日本語 Japan English Jordan English Kazakhstan Русский Kazakhstan English Kenya English Kuwait English Kyrgyzstan Русский Kyrgyzstan English Latvia English Lithuania English Malaysia English Mauritius English Mauritius français (Maurice) Mexico Español Mexico English Moldova Română Moldova English Mongolia English Morocco English Morocco Français Mozambique Português Mozambique English Netherlands Nederlands Netherlands English New Zealand English Nigeria English Norway English Oman English Pakistan English Paraguay Español Paraguay English Peru Español Peru English Philippines English Poland Polski Poland English Portugal Português Portugal English Qatar English Republic of Korea 한국어 Republic of Korea English Romania Română Romania English Saudi Arabia English Serbia Српски Serbia English Singapore English Slovakia English Slovenia English South Africa English Spain English Spain Español Sri Lanka English Sweden English Switzerland Deutsch Switzerland Français Switzerland Italiano Switzerland English Tanzania English Thailand ไทย Thailand English Togo English Togo Français Tunisia English Tunisia Français Türkiye Türkçe Türkiye English Turkmenistan Русский Turkmenistan English Ukraine Українська Ukraine English United Arab Emirates English United Kingdom English Uruguay Español Uruguay English USA English Uzbekistan English Uzbekistan Русский Vietnam Tiếng Việt Vietnam English

Anti-Galling Performance Testing of Nitrided Layers: Standards, Methods, and Applications

Nitrided layers are widely applied to prevent galling, scuffing, and seizure in highly loaded sliding components such as valve stems, gear shafts, pump plungers, and threaded fasteners. This article explains how accredited third-party laboratories evaluate the anti-galling (anti-seizure) performance of nitrided surfaces using recognized standards such as ASTM G98, ASTM G99, ASTM G77, ASTM G133, ISO 14635, ISO 18203, and GB/T 11354. It covers the technical background, sample requirements, testing items, testing methods, industrial applications, and frequently asked questions for design engineers, heat-treatment specialists, and quality managers.

Technical Overview

Nitriding is a thermochemical surface-hardening process—including gas nitriding, plasma (ion) nitriding, and salt-bath nitrocarburizing—in which nitrogen diffuses into the steel surface to form a hard compound layer (also called the white layer, consisting mainly of epsilon-Fe3N and gamma'-Fe4N iron nitrides) on top of a nitrogen-enriched diffusion zone. Depending on the alloy content, nitrided surfaces typically reach 700 to 1200 HV surface hardness, with a compound layer of roughly 5 to 30 micrometers and a total nitriding hardness depth of a few tenths of a millimeter. The nitrogen-saturated compound layer is chemically stable and metallically inert in character, which strongly suppresses microwelding between contacting asperities, lowers the sliding friction coefficient, and dramatically raises resistance to scuffing and seizure.

Galling (also referred to as seizure or scuffing) is a localized adhesive failure mode that occurs when sliding surfaces cold-weld at asperity junctions and then tear apart, producing material transfer, severe surface damage, and in extreme cases complete mechanical locking of the assembly. Anti-galling performance testing of nitrided layers quantifies the threshold contact stress or load at which this adhesive damage initiates under controlled sliding conditions, and correlates the result with the metallurgical quality of the nitrided case. Tribological testing is therefore normally combined with structural verification—microhardness profiling, nitriding hardness depth measurement, and compound layer thickness and porosity rating—so that the anti-galling result can be linked to specific nitriding process parameters. Such testing is routinely performed by accredited third-party laboratories for process qualification, product acceptance, and failure analysis.

Testing Samples

Production Parts and Witness Coupons

Actual nitrided components are tested whenever the delivered surface condition is decisive. Typical parts submitted for anti-galling evaluation include crankshafts, camshafts, valve stems and seats, fuel-injection plungers and barrels, gear shafts, hydraulic rods, pump sleeves, extruder screws, die inserts, and threaded fasteners. When finished parts cannot be sacrificed, witness coupons made from the same steel grade are nitrided in the same furnace load and used as representative specimens.

Standard Tribological Specimens

Laboratory specimens are machined to the geometry required by the selected test standard, for example flat-bottomed cylindrical buttons for button-on-block galling tests, pins and discs for pin-on-disc tests, rectangular blocks and rings for block-on-ring tests, and flat plates with counterbodies for reciprocating tests. The following conditions should be documented for every test series:

  • Steel grade, metallurgical state (quenched and tempered hardness), and nitriding process parameters (gas, plasma, or salt bath; temperature; time; gas composition)
  • Surface condition: as-nitrided, ground, or polished, with measured surface roughness, typically Ra below 0.4 to 0.8 micrometers for galling tests
  • Compound layer thickness, porosity level, and nitriding hardness depth determined on cross-sections per ISO 18203 or GB/T 11354
  • Careful degreasing and handling to exclude contaminant films that would distort friction and adhesion results
  • Sufficient replicates (commonly at least three per condition) to account for the statistical scatter typical of galling phenomena

Mating (Counterface) Specimens

The counterface material must be defined because anti-galling behavior is a property of a material couple, not of a single surface. Common configurations include self-mated nitrided couples, nitrided steel against through-hardened bearing steel, nitrided against stainless steel, and nitrided against bronze or coated counterfaces. Counterfaces should come from the same material lot and receive the same surface finish specification as the production mating part.

Testing Items

Anti-galling evaluation of nitrided layers typically combines tribological performance indicators with supporting metallurgical characterization:

  • Threshold galling stress: the highest contact pressure at which sliding occurs without galling, determined by the button-on-block method
  • Critical seizure or scuffing load: the load level at which friction rises abruptly, surfaces weld, or the driving torque exceeds a defined limit
  • Failure load stage in standardized gear scuffing rigs, expressed as a load stage number
  • Static and kinetic friction coefficients under dry and lubricated conditions
  • Wear rate and wear volume, obtained from mass loss and wear-scar profilometry
  • Surface damage classification: no damage, slight galling, severe galling, or complete seizure, supported by optical and scanning electron microscopy of transferred material
  • Fastener friction coefficients and seizure torque for threaded assemblies
  • Supporting items: surface and case microhardness per ISO 6507-1 or GB/T 4340.1, nitriding hardness depth per ISO 18203 or GB/T 11354, compound layer thickness and porosity rating, microstructure, and surface roughness before and after testing

Testing Methods

Button-on-Block Galling Test (ASTM G98)

The flat end of a cylindrical button is pressed against a flat block and slowly rotated through 360 degrees under a defined load. The load is increased in successive steps, each time on a fresh track, until galling is observed visually at low magnification. The threshold galling stress is reported as the highest stress at which no galling occurred, usually as the average or lowest value of the replicates. This method is the most widely recognized screening test for nitrided couples, and the related ASTM G196 procedure offers improved ranking discrimination between similar material pairs. Self-mated nitrided steel couples typically sustain far higher threshold galling stresses than untreated or through-hardened steel couples.

Unidirectional Sliding Tests (ASTM G77 Block-on-Ring, ASTM G99 Pin-on-Disc)

In block-on-ring and pin-on-disc configurations, the nitrided specimen slides continuously against a rotating ring or disc under constant or stepwise increasing load while friction force is recorded. The transition from mild running wear to severe adhesive wear, marked by a sharp friction rise and rapid material loss, identifies the scuffing limit of the nitrided surface. These methods are suitable for ranking nitriding process variants, post-nitriding finishing operations, and lubricants, and ISO 20808 may be applied to nitrided and coated surfaces.

Reciprocating and Oscillating Tests (ASTM G133)

High-frequency, small-amplitude reciprocating sliding reproduces the contact conditions of valve seats, actuator screws, and oscillating bushes. Tests are run dry and lubricated at controlled temperature, and the onset of galling is detected through friction spikes, stick-slip behavior, and post-test inspection of the wear scar.

Pin-and-V-Block Seizure Load Test (ASTM D3233)

The pin-and-V-block method ratchets the load upward in stages until the sliding surfaces weld together and the machine stalls. The recorded seizure load quantifies the combined anti-galling effect of the nitrided surface and the lubricant, and the method is frequently used to qualify surface and lubricant combinations for oilfield pumping equipment and threaded connections.

Gear Scuffing Tests (ISO 14635-1, ASTM D5182)

Standardized back-to-back gear test rigs of the FZG type run gear pairs through progressively higher load stages until scuffing striations appear on the flanks. The failure load stage provides a comparative measure of the scuffing resistance of nitrided gear flanks and is used to qualify gear materials, nitriding treatments, and gear oils for transmission applications.

Fastener Torque-Tension Tests (ISO 16047)

Nut-and-bolt or stud-and-nut assemblies with nitrided or nitrocarburized threads are tightened under controlled conditions to determine the thread and under-head friction coefficients and the torque at which threads seize or strip. This directly validates the anti-galling function of nitriding on high-temperature bolting and exhaust-system fasteners.

Supporting Metallurgical Characterization

Because anti-galling performance depends on case quality, every tribological campaign should be accompanied by metallographic verification: microhardness traverses at HV0.5 or HV1 per ISO 6507-1 or GB/T 4340.1, nitriding hardness depth per ISO 18203 or GB/T 11354, compound layer thickness, porosity and nitride network ratings per GB/T 11354, and documentation of surface roughness. This allows the reported galling threshold to be traced back to controllable nitriding parameters.

Applications

Anti-galling performance testing of nitrided layers supports design release, process qualification, and failure prevention across many industries:

  • Automotive and commercial vehicles: crankshaft journals, camshafts, tappets, fuel-injection components, gear shafts, and synchronizer parts
  • Oil, gas, and pumping systems: sucker-rod pump barrels and plungers, valve stems, gates and seats, and threaded tool connections
  • Fluid power and machine tools: hydraulic cylinder rods, spools, ball-screw nuts, spindle shafts, and guide bushings
  • Plastics, rubber, and die casting: extruder screws and barrels, injection-mold components, hot-work die inserts, core pins, and ejector pins
  • Fastening technology: turbine and exhaust studs, nuts, and threaded inserts where thread galling must be excluded
  • Aerospace and actuation: plasma-nitrided precipitation-hardening stainless components, actuator screws, and landing-gear bushings

Beyond routine acceptance testing, the results are used to compare gas versus plasma nitriding process windows, to balance compound layer thickness against fatigue and toughness requirements, and to benchmark nitrided surfaces against nitrocarburized or PVD-coated alternatives during root-cause investigations of field seizure failures.

FAQ

What does anti-galling performance mean for a nitrided layer?

It is the ability of the nitrided surface, especially the hard iron-nitride compound layer, to slide against a mating surface without cold welding, material transfer, or seizure up to a defined contact stress. Testing expresses this as a threshold galling stress or a critical seizure load for a specific material couple.

Which standards are most commonly applied?

ASTM G98 is the primary method for threshold galling stress, complemented by ASTM G99, ASTM G77, and ASTM G133 for friction and wear, ASTM D3233 for seizure load, and ISO 14635-1 for gear scuffing. Case quality is verified per ISO 18203, ISO 6507-1, GB/T 4340.1, and GB/T 11354.

Should specimens be tested as-nitrided or after finishing?

Specimens should be tested in the exact surface condition delivered to service, because grinding or polishing after nitriding changes the compound layer, porosity distribution, and roughness, all of which influence galling behavior. Many programs test both as-nitrided and finished states for comparison.

How is galling detected during a test?

Galling is identified by visual and microscopic evidence of torn, burnished, or furrowed surfaces with adhered transferred material, together with abrupt increases in friction force or torque during the test. Mass change and wear-scar profilometry confirm the severity of adhesive damage.

Does a thicker compound layer always improve anti-galling performance?

Not necessarily. Galling resistance generally improves up to an optimum compound layer thickness, often in the range of roughly 10 to 20 micrometers, but excessively thick or porous compound layers can become brittle and spall under high contact stress. The optimum must be balanced against fatigue and impact toughness requirements, which is why tribological and metallographic results are evaluated together.

Can the tests be run under lubrication?

Yes. Dry tests provide the most conservative assessment of the intrinsic anti-galling capacity of the nitrided layer, while lubricated tests with a documented lubricant reproduce actual service conditions. Both conditions are frequently included in a single test program.

How are acceptance criteria established?

Because threshold values are couple- and condition-specific, acceptance limits are usually set by comparison with proven reference lots or by qualification testing agreed between manufacturer and purchaser. Accredited third-party laboratories report results strictly according to the cited standard so that data remain comparable between suppliers and production batches.

Why Choose ZKGX?

  • State-of-the-art analytical equipment
  • Highly qualified scientific team
  • Fast turnaround time
  • Competitive pricing